The db300 is “Blue UAS” approved. This means that the module fulfills the drone requirements set by
the U.S. Department of Defense/War for government use, ensuring they meet strict security and
operational standards. The db300 has been approved on July 10th 2026 and can be found on the official framework list: https://tyrionprod.servicenowservices.com/gsp?id=framework_list search for db300

Specifications

Remote ID transmission protocols
Bluetooth dual-mode (Bluetooth 4 Legacy + Bluetooth 5 Long Range)
FCC/CE certified radio module
*u-blox BMD-345
*Nordic nRF52840 radio
* External PA 24 dB
Transmit frequency:
* 2.4 GHz
Transmit power
* up to +18 dBm (FCC certified)
Antenna: 2 dBi omni-directional antenna with IPEX connector (included)
Compliant with international regulation
(+20 dBm EIRP / 100 mW with the included 2 dBi antenna)
*EU ASD-STAN DIN EN 4709-002
*USA ASTM Remote ID Standard ASTM F3411-22a-RID-B/ F3586-22
Connectivity:
*2x JST GH 4-pin CAN (DroneCAN) port
CAN 2.0 (1 Mbps) / CAN FD (up to 8 Mbps)
120 ohm termination: solder pad
*1x JST GH 6-pin TELEM (UART/MAVLink) port
57600 baud rate (can be configured to different baudrate)

Power:          +5V supplied from TELEM or CAN port
LED lights:  power (white) and status LED (red)
Fastening     mechanism: 4x M2 screws (20 x 20 mm grid)
Size:              27.5 x 27.5 x 5 mm
Weight:        2.5 g (excluding antenna)
Operating temperature: -40°C to +85°C
NDAA: Sections 848 and 889, plus Blue UAS approval

The post DroneBeacon db300 Blue UAS approved Remote ID module (MAVLink/DroneCAN) appeared first on DroneScout.

Receive popular drones with RemoteID and convert it to a wireless signal that most smartphones (iOS/Android) understand. You can keep using your favorite RemoteID app. Or use our free DroneScout pro app.

Product Page

The post DroneScout Bridge triple-band ds110 retail, RemoteID receiver for iOS, Android and drone appeared first on DroneScout.

Receive popular drones with RemoteID and convert it to a wireless signal that most smartphones (iOS/Android) understand. You can keep using your favorite RemoteID app. Or use our free DroneScout pro app.

Product Page

The post DroneScout Bridge triple-band ds111 retail, RemoteID receiver for iOS, Android and drone appeared first on DroneScout.

Receive popular drones with RemoteID and convert it to a wireless signal that most smartphones (iOS/Android) understand. You can keep using your favorite RemoteID app.

Product Page

The post DroneScout Bridge ds100 retail, RemoteID receiver for iOS, Android and drone appeared first on DroneScout.

Receive popular drones with RemoteID and convert it to a wireless signal that most smartphones (iOS/Android) understand. You can keep using your favorite RemoteID app.

Product Page

The post DroneScout Bridge ds101 RemoteID receiver for iOS, Android and drone appeared first on DroneScout.

Receive popular drones with RemoteID and convert it to a wireless signal that most smartphones (iOS/Android) understand. You can keep using your favorite RemoteID app.

Product Page

The post DroneScout Bridge ds100 RemoteID receiver for iOS, Android and drone appeared first on DroneScout.

The transponder has both a battery and GNSS receiver.

It can be mounted on a drone using the provided 3M dual-lock stickers.

Product Page

The post DroneBeacon db150 RemoteID Broadcast Module with battery (out of stock, new stock ETA end of Nov 2026) appeared first on DroneScout.

The transponder has both a battery and GNSS receiver.

It can be mounted on a drone using the provided 3M dual-lock stickers.

June 2024: see this product notification 

Product Page

The post DroneBeacon db120 RemoteID Broadcast Module with battery appeared first on DroneScout.

It is a PCB and needs an external GNSS (GPS) receiver (NMEA or UBX). 

It relays the GNSS information via the GPS out connector to the flight controller. All connectors are solder pads on a 1.27 mm grid. An antenna is provided (WLAN/BLE). The board and attached GNSS receiver are powered via the + and – solder pads (4.75 to 15V).  The size of the board is only 19 x 14 mm and the weight is just 2 grams (including antenna).

Product Page  Manual

The post DroneBeacon db153fpv RemoteID tiny Broadcast Module 19×14 mm appeared first on DroneScout.

The DroneBeacon db152fpv is a small, but powerful (direct/broadcast) stand-alone Remote ID transponder for drones with 20 x 20 M3 holes and needs an external GNSS receiver. It is designed for FPV drones and supports any GNSS receiver with NMEA or UBX (u-blox) protocol. Of course, it can be used for other drones as well.

It is a PCB and needs an external GNSS (GPS) receiver (NMEA or UBX). 

It relays the GNSS information via the GPS out connector to the flight controller. The connectors are 6-pin JST-SH 1 mm. An antenna is provided (WLAN/BLE). The board and attached GNSS receiver are powered via the VCC pin of the GPS OUT port (4.75 to 15V). The db152fpv has a 20 x 20 grid with M3 holes for easy installation. The size of the board is 27 x 27 mm and the weight is 2.9 gram (including antenna).

Product Page  Manual

The post DroneBeacon db152fpv RemoteID Broadcast Module 20×20 M3 appeared first on DroneScout.